Operation game how does it work

Press ESC to cancel. Skip to content Home Articles What are the rules for the game Operation? Ben Davis February 25, What are the rules for the game Operation? How many batteries does operation take? What age is Operation game for? How old is the Operation game? Is there money in Operation game? How much money is in operation game? What are the body parts in the game Operation? How many body parts are in an operation?

How many ailments of surgery are there? In Challenge 1, you will set up the game board. In Challenge 2, you will make the electrical connections and try your hand at performing operations on your patient! The Operation game is built from two layers of foam board. The top layer has an image of "Cavity Sam" or some other patient image that you choose , while the bottom layer is covered in aluminum foil.

The aluminum foil is part of the game's electronic circuit, which you wire together in Challenge 2. The "Cavity Sam" image from the original Operation game is shown in the figure below, and a printable version is available below as a PDF. Any other image- a TV character, a movie star, or even a photo of a friend- can also be used, provided that it fits on the game's top panel, which you will cut out in the next step.

The top panel for your game is a rectangular piece of foam board, measuring about 6 inches by 11 inches. NOTE: The size of the top panel should be the same width as your patient image, but 2 inches longer.

If you are using your own image, adjust the size of your top panel accordingly. Mark your measurements on the foam board. Make your cuts with the utility knife, using the cutting mat to protect your work surface, as shown in Figure. NOTE: Use a metal straight edge as well as a new sharp blade to avoid the blade catching on the foam board.

The patient image should be secured to the top panel with glue from a glue stick. It is important to align the image properly, so pay close attention when gluing it down. Apply a thin layer of glue to the back of your image, as shown in Figure. Be sure to cover the entire surface evenly.

Press the image into place, aligning the bottom edge of the image with the bottom edge of your top panel, as shown in Figure. NOTE: There should be about 2 inches of uncovered space at the top of the panel. In this step, you will cut out several small sections of the game's top panel, including the operation site- places where players will operate on your patient.

You will also cut out a rectangular opening for the buzzer, and a small circular opening for a screw that will anchor one of the battery leads. Make an outline around your patient's operation sites, as shown in Figure. NOTE: The spots that are pre-marked on the "Cavity Sam" image are a bit too small; you should make yours a little larger, as shown.

Trace an outline of the buzzer on the area of the panel above the patient's head, as shown in Figure. The outline should be tight and precise, so that the buzzer will fit snugly in the opening.

Cut out each of your marked pieces, as shown in Figure. NOTE: Be very careful not to cut outside your marks, and not to cut your finger! In the next step, you will add a bottom panel to your game, wrapping it in aluminum foil. Aluminum and other metals are very good at carrying electricity in circuits- these materials are known as conductors Figure.

Other materials do not carry electricity very well at all- these materials are known as insulators. Good insulators include certain types of plastic and rubber.

The power cords for household electrical appliances, such as lamps and fans, have a conductor inside usually copper that is coated with a plastic insulator. This way, electricity can flow through the cord, but it cannot escape from the circuit if the cord comes in contact with another conductor like your hand!

The game's bottom panel provides backing for your patient's operation sites. It is wrapped in foil, so that it can conduct electricity to other components in the game's circuit.

Cut out your bottom panel, making it about 4 inches shorter than your top panel. Wrap your bottom panel in a smooth layer of aluminum foil, as shown in Figure. Tape the foil in place, if necessary. Test fit your bottom panel to make sure that it provides backing for all of your patient's operation openings, as shown in Figure. NOTE: The bottom panel should also be visible in the hole for the battery lead, but not reach as high as the patient's nose.

Glue the top panel to the bottom panel, as shown in Figure. The circuit for the Operation game is fairly simple. The red lead from the battery is connected to the foil-wrapped bottom layer. Charlene DeLoach January 6, Operation is a classic family fun game that has been a staple in homes since when it was originally distributed by Milton Bradley. Decades later, Hasbro is still cranking out new versions of the stress-inducing game, featuring characters like Olaf from Disney Frozen.

Buy it Now The Toy Insider participates in affiliate programs that may generate revenue for the site when a purchase is made through the links below. More You'll. Charlene is a lawyer turned influencer who loves play, puns, and anything with pink. She has her own blog chronicling her love of toys PlayroomChronicles. Her specialty is advising parents about the best toys for children with neuro-differences - and loves to discuss Disney for days.

Leave this field empty. Hot STEM Industry Trends. Subscribe to Our Newsletter! Pop Trends. This website uses cookies that help the website function and help us understand how to interact with it. We use these cookies to provide you with an improved user experience. If you continue to visit our website, we assume you are OK with it.